|
New Equipment: By Type | By Manufacturer
|
|
All Listings >
Category: SAWS - CUT-OFF & MITER
1-10 || 11-20 || 21-30 || 31-37
New Machine Listings
|
|
|
CROSSCUT SOLUTIONS - CS14M SEMI-AUTOMATIC CUT-OFF SAW
|
|
Price: $6,795.00
Machine Stock Number: CS14M-Q
Condition: New
FOB: WI-MANAWA
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
Mechanically operated crankshaft and clutch arrangement offers extremely fast and smooth cutting action. NO compressed air required! 2" x 8" capacity, 7.5 HP TEFC motor, magnetic starter with 110 volt control voltage, standard cycle speed of 133 cycles/minute. 14” saw blade not included. (Please state voltage and hand of the saw...available in right or left hand).
Options:
Saw Blade 14” diameter, 1” bore, 100 tooth carbide tipped $190.00
8’ Infeed Roller Conveyor, Model CS0116, with saw brackets and legs,
rollers on 1’ centers, decked between the rollers. $625.00
12' Infeed as above, CSO044 $875.00
Cycle Speed; the standard cycle speed is 133 cycles/ minute. If a fine cut is required for the application, slowing the cycle speed down can increase the quality of the cut. Cycle speeds of 66 and 94 cycles/ minute are available upon request.
If configured at the time of order with 66 cycles/minute ADD $ 80.00
If configured at the time of order with 94 cycles/minute ADD $ 50.00
Tigerstop Ready - Electrical interlock plus sides drilled/brackets for tables $420.00
Terms: 30% down with the order, 60% prior to shipment and 10 % due upon receipt of machine and invoice.
|
|
|
|
|
CROSSCUT SOLUTIONS - CS14P PNEUMATIC CUT-OFF SAW
|
|
Price: $5,795.00
Machine Stock Number: CS14P-Q
Condition: New
FOB: WI-MANAWA
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
2" x 8" capacity, 7.5 HP TEFC motor, magnetic starter with 110 volt control voltage, adjustable cutting cycle speed of up to 90 cycles/minute, 14” saw blade NOT included. (Please state the voltage and the hand of the saw - available in right or left hand.) Heavy duty American made saw for two to three shift operation! Electric foot switch; heavy duty air cylinder with pneumatic integrated cushions on the top and bottom of the cylinder, plus large 1” diameter rod is used to increase the longevity of the cylinder. A UL approved starter panel is used with 110 volt controls and starter sized for either voltage - just need to change heaters. All saws include either a clear hand guard or the expanded steel hand guard to keep the operator’s hand farther away from the cutting envelope. Easy access through the rear panel area when it is removed from the saw during maintenance. The top cover hinges up to also access the inside through the top of the saw. Maintenance people are extremely pleased with this design.
Optional:
Saw Blade 14” diameter, 1” bore, 100 tooth carbide tipped $190.00
Crosscut Solutions 8’ Infeed Roller Conveyor, Model CS0042, with saw
brackets and legs, rollers on 1’ centers, decked between the rollers. $625.00
12' Infeed as above, CSO044 $875.00
Tigerstop Ready - Electrical interlock plus sides drilled/brackets for tables $420.00
Terms: 30% down with the order, 60% prior to shipment and 10 % due upon
receipt of machine and invoice.
|
|
|
|
|
CROSSCUT SOLUTIONS - CS18M SEMI-AUTOMATIC CUT-OFF SAW
|
|
Price: $7,295.00
Machine Stock Number: CS18M-Q
Condition: New
FOB: WI-MANAWA
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
Mechanically operated crankshaft and clutch arrangement offers extremely fast and smooth cutting action. NO compressed air required! 2" x 12" capacity, 7.5 HP TEFC, motor, magnetic starter with 110 volt control voltage, standard cycle speed of 133 cycles/minute. 18” saw blade NOT included. (Please state voltage and hand of the saw...available in right or left hand).
Options:
To convert at time of order to 4" x 8" capacity and 94 cycles/min. add $180.00
Saw blade, 18" diameter, 1" bore, 100 tooth carbide tipped $280.00
8’ Infeed Roller Conveyor, Model CS0042, with saw brackets and
legs, rollers on 1’ centers, decked between the rollers. $625.00
12' Infeed as above, CSO044 $875.00
Cycle Speed; the standard cycle speed is 133 cycles/ minute. If a fine cut is required for the application, slowing the cycle speed down can increase the quality of the cut. Cycle speeds of 66 and 94 cycles/ minute are available upon request.
If configured at the time of order with 66 cycles/minute ADD $ 80.00
If configured at the time of order with 94 cycles/minute ADD $ 50.00
Tigerstop Ready - Electrical interlock plus sides drilled/brackets for tables $420.00
Terms: 30% down with the order, 60% prior to shipment and 10 % due upon receipt of machine and invoice.
|
|
|
|
|
CROSSCUT SOLUTIONS - CS18P PNEUMATIC CUT-OFF SAW
|
|
Price: $6,295.00
Machine Stock Number: CS18P-Q
Condition: New
FOB: WI-MANAWA
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
2" x 12" capacity, 7.5 HP TEFC motor, magnetic starter with 110 volt control voltage, adjustable cutting cycle speed of up to 90 cycles/minute, 18” saw blade NOT included. (Please state the voltage and the hand of the saw - available in right or left hand.) Heavy duty American made saw for two to three shift operation! Electric foot switch; heavy duty air cylinder with pneumatic integrated cushions on the top and bottom of the cylinder, plus large 1” diameter rod is used to increase the longevity of the cylinder. A UL approved starter panel is used with 110 volt controls and starter sized for either voltage - just need to change heaters. All saws include either a clear hand guard or the expanded steel hand guard to keep the operator’s hand farther away from the cutting envelope. Easy access through the rear panel area when it is removed from the saw during maintenance. The top cover hinges up also to access the inside through the top of the saw. Maintenance people are extremely pleased with this design.
Optional:
To convert at time of order to 4" x 8" capacity and variable cycles/min. - add $180.00
Saw blade, 18" diameter, 1" bore, 100 tooth carbide tipped $280.00
Crosscut Solutions 8’ Infeed Roller Conveyor, Model CS0042, with saw
brackets and legs, rollers on 1’ centers, decked between the rollers. $625.00
12' Infeed as above, CSO044 $875.00
Tigerstop Ready - Electrical interlock plus sides drilled/brackets for tables $420.00
Terms: 30% down with the order, 60% prior to shipment and 10 % due upon
receipt of machine and invoice.
|
|
|
|
|
CTD - 400 SERIES MITER/CUT-OFF SAW
|
|
Price: $7,795.00
Machine Stock Number: 400-Q
Condition: New
FOB: CA.
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
All 400 Series Machines include 7-1/2 H.P. 3 Phase, TEFC Motors; Magnetic Starter with push button in cover; Arbor 1” with 5” saw collars; Floor Stand; Standard Fences; Hand Operated; Two 4” Dust outlets; 48” wide x 40” deep x 70” high. Weight 850 lbs. Power Downfeed of saw head is optional. "M" miter models pivot 45 degrees each way on 16" diameter disc.
MODEL M416, mitre base, 16” blade capacity $7,795.00
MODEL F426, straight cut, 16” blade capacity $7,295.00
MODEL M516, mitre base, 20” blade capacity $7,995.00
MODEL F526, straight cut, 20” blade capacity $7,495.00
OPTIONAL:
10H - 10 H.P. TEFC motor $ 400.00
HYD - Air Hydraulic Power Feed. Safety anti-tie down, maintained
contact two-hand control. Light duty vertical air clamp, air filer/
regulator/lubricator unit with auto drain 16" $2,695.00
20" $2,795.00
AF - Air power feed unit - same as HYD, but no hydrocheck unit $1,995.00
PR - Pressure regulator—for clamps or vises; adjusts pressure $ 100.00
VC/400 - Vertical clamp—light duty, 3" Stroke $ 285.00
VAV - Vertical air vise—heavy duty $ 435.00
SLS - Sawblade lubrication system—automatic $ 395.00
BIOL - CTD biolube lubrication system $1,475.00
B3P141 - CTD biolube lubricant per gallon $ 65.00
RC-10 - Roller conveyor—10’ long; 7 rollers per section $ 575.00
TIG - Add brackets for easy mounting of Tigerstop tables $ 350.00
TERMS: 25% down with order, balance net 30 days from shipment, with approved credit
|
|
|
|
|
CTD - CM60 MITER/CUT-OFF SAW
|
|
Price: $7,495.00
Machine Stock Number: CM60-Q
Condition: New
FOB: CA-L.A.
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
16" blade capacity (1" bore) Compound Miter and Cut-Off Saw with 3 HP TEFC main motor, magnetic starter with push button in cover. Includes floor stand, standard fences; hand operated; miter 45 degrees to the right, compound up to 45 degrees same direction. Size is 35" wide by 40" deep by 70" high; weight 550 lbs.
Cutting Capacities:
45 degree miter - 4" high x 7.25" wide
90 degree straight - 4" high x 10.5" wide
90 degree straight + 45 degree compound - 2-5/8" x 10"
Optional:
5H - 5 HP TEFC motor $ 290.00
5 HP TEFC single phase 220 volt and controls $ 650.00
HYD - Air Hydraulic Power Feed. Safety anti-tie down, maintained
contact two-hand control. Light duty vertical air clamp, air filer/
regulator/lubricator unit with auto drain $2,695.00
AF - Air power feed unit - same as HYD, but no hydrocheck unit $1,995.00
PR - Pressure regulator—for clamps or vises; adjusts pressure $ 100.00
VC/400 - Vertical clamp—light duty, 3" Stroke $ 285.00
SLS - Sawblade lubrication system—automatic $ 395.00
BIOL - CTD biolube lubrication system $ 1,475.00
B3P141 - CTD biolube lubricant per gallon $ 65.00
RC-10 - Roller conveyor—10’ long; 7 rollers per section $ 575.00
with PVC rollers add $ 150.00
TIG - Add brackets for easy mounting of Tigerstop tables $ 350.00
TERMS: 25% down with order, balance net 30 days from shipment, with approved credit
|
|
|
|
|
CTD - D-45AX SAW-DBL MITER
|
|
Price: $7,495.00
Machine Stock Number: D45AX
Condition: New
FOB: CA-L.A.
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
Fixed head double miter saw, 12" blade capacity standard, 1-1/2 HP, 1 phase 220 Volt or 3 phase 220/440 volt TEFC motors, Nema 56 frame, 2 belt drive with dual magnetic starter; adjustments for blade variation allows precision alignment of blades to minimize scrap; saw heads adjustable up to 3 degrees for assurance of perfect miters; 35" high table of heavy cast iron. Floor stand completely enclosed with 6" dust collector outlet, includes scrap chute; keyed fences, adjustable front to rear. Precision machined and ground saw arm, pivot brackets and table, with milled slots to guide pivot brackets and fences; 2" diameter air cylinder with adjustments for speed, stroke length, and position of blade above work. Actuation by pnuematic spring return foot valve; air filter/regulator with auto drain. See literature for capacities.
Optional:
2H1 - Add for 2 HP, 1 PH. Motors $ 260.00
14"HT - 14" blade capacity (2 HP, 3 ph motors) $ 495.00
FEX - 10' capacity length gauge with tape and stop $ 335.00
SWS - 10' cap. Swing stop gauge with 4 swing stops $ 495.00
Extra swing stops for SWS gauge (200BE50) $ 45.00 ea.
VC3 - Vertical air clamps, 3" stroke, auto release $ 215.00 ea.
HC3 - Horizontal air clamps auto release $ 230.00 ea.
PR - Pressure regulator for pneumatic clamps $ 120.00
SLS - Spray mist applicator with auto valve $ 295.00
BIOL - Biolube lubrication system $ 1,475.00
B3P141 - Biolube lubricant, per gallon $ 65.00
ATD - Two hand anti-tie down controls for saw cycle $ 495.00
POP - 12" dia x 1" bore 80 tooth CT blade for aluminum $ 145.00 ea.
POP - 14" dia x 1" bore 100 tooth CT blade for aluminum $ 185.00 ea
Terms: 25% down with order, balance net 30 days with approved credit.
|
|
|
|
|
CTD - DM-200R DOUBLE END MITER SAW
|
|
Price: $12,295.00
Machine Stock Number: DM200
Condition: New
FOB: CA-L.A.
Electrical: 230/460 V, 3 Ph, 60 Cy
|
 |
Description:
12" blade capacity, double end trim and miter saw with following standard equipment: 2 HP 3 phase TEFC motors with magnetic starters; right and left heads are mounted on top tables graduated each degree and adjustable from 90 to 45 degree toward each other; 45 and 90 degree stops. Keyed fences on both sides of each blade are adjustable; right hand carriage is moveable up to 8' between centers on rack and pinion; cut length measuring scale is adjustable and reads left to right.
Air arm power feed units are located to the rear of the machine. Saw heads are actuated by a safety anti-tie down, maintained contact two hand control mounted above left saw head; saws reverse when two hand control is released; up and down stroke speed controls provided; two vertical inside air clamps actuated by a foot valve are supplied; clamps must be actuated prior to operating two hand control; air filter-regulator- lubricator with auto-drain is provided.
Optional:
3H3 - 3 HP motors in lieu of 2 HP $ 220.00/pair
HCO - Two horizontal air clamps (outside mounting) $ 425.00
HCI - Two horizontal air clamps (inside mounting) $ 425.00
AL - Additional length capacity (per 2') to 18" $ 325.00
CWS - Center work support with vertical clamp $ 525.00
MLF - Motorized length feed - right hand $ 1995.00
12" x 90 tooth C.T.. blades $ 235.00 ea.
Shipment: approx. 5-6 weeks aro.
Terms: 30% with order, balance net 30 with approved credit.
|
|
|
Click for a larger picture
|
|
CTD - DM-400 DOUBLE END TRIM & MITRE SAW
|
|
Price: $23,995.00
Machine Stock Number: DM400-Q
Condition: New
FOB: CA-L.A.
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
16" blade capacity, double end trim and miter saw with the following standard equipment: 7 1/2 HP 3 phase TEFC motors; with magnetic starters. Includes two standard right hand 16” 400 heads mounted on top of tables graduated each degree and adjustable from 90 to 45 degree toward each other; 45 and 90 degree stops; keyed fences on both sides of each blade are adjustable; right hand carriage is moveable up to 8' between centers on rack and pinion. Cut length measuring scale is adjustable and reads left to right.
Air arm power feed units are adjustable for setting height of blade above work; saw heads are actuated by a safety anti-tie down, maintained contact two hand control mounted above left saw head; saws reverse when two hand control is released;up and down stroke speed controls provided; two vertical inside air clamps actuated by a foot valve are supplied; clamps must be actuated prior to operating two hand control; Air filter-regulator- lubricator with auto-drain is provided. Four 4” dust outlets supplied.
Optional:
Add for 20" blade capacity DM 400 $ 1,100.00
10H3 - Add for 10 HP TEFC motors $ 900.00
BIOL - CTD Biolube lubrication system; four nozzles pulse
Spray a minute amount of biodegradeable lub for cleaner,
More efficient job. Inculdes air filter and pint of oil. $ 1,895.00
AL - Add for additional length capacity, each 2’ up to 14’ $ 525.00/2'
CWS - Center work support for long parts; includes keyed
Vertical clamp $ 625.00 ea.
DIG/LTH - Digital length measurement / readout $ 1,500.00
MLF - Motorized length feed of saw head $ 2,500.00
Terms: 30% down with order, balance net 30 with approved credit.
|
|
|
|
|
CTD - F255R MITER CHOP SAW
|
|
Price: $2,495.00
Machine Stock Number: F255R-Q
Condition: New
FOB: CA-L.A.
Electrical: 230/460 V, 3 Ph, 60 Cy
|
 |
Description:
MODEL F255R Overhead cut off saw NON-MITERING 90 degree cut only with 12” blade capacity; 2 HP, 1 phase 230 volt or 3 phase 230 volt TEFC motor; V-Belt drive includes rotating blade guard with 2” dust outlet, less blade. Standard machine with full table base, 2 keyed sliding fences and manual overload starter. $2,495.00
MODEL M25R Overhead cut off saw MITERING with indexing angle presets; standard machine with full table base as above $2,795.00
Options:
FSD - Enclosed floor stand with dust pan and 4" dust outlet $ 495.00
MAG – Magnetic starter – OSHA required; gives motor high
and low voltage protection with fuse protection and disconnect
switch; not available for single phase, 110 volt motors $ 350.00
VOLT – Voltage change - to change voltage from 220 volt to
either 110 or 440 volt (no charge if Magnetic Starter is purchased) $ 75.00
3H3 – 3 HP, 3PH TEFC Motor $ 110.00
LEFT – Left Hand Assembly – opposite of standard arm; to
feed material to the right $ 120.00
AF – Air Power Feed Unit – for precision, controlled cutting
on wood, plastic or non-ferrous sections; actuated by SAFETY
ANTI-TIE DOWN, MAINTAINED CONTACT TWO-HAND
CONTROL. Air vales are mounted above the saw head and reverse
when two-hand control is released; includes one AIR CLAMP,
FOOT VALVE to actuate clamp and AIR FLITER/EGULATOR/
LUBRICATOR UNIT with AUTO DRAIN. $1,795.00
HYD – Air Haydraulic Power Feed Unit – same as AF but uses a
Hydrocheck Unit with Air Cylinder for controlled down stroke
speed, includes FV to actuate clamps. $2,450.00
FR – Combination Air Filter/Regulator/Lubricator – to clean
incoming air; with Auto Drain $ 200.00
RC-10 – Roller Conveyor – fastened to Floor Stand, one leg and
seven rollers per section; 10’ long $ 575.00
QV - Quick action manual vise clamping $ 295.00
Terms: 30% down with order, balance net 30 with approved credit.
|
|
|
Click for a larger picture
|
|
CTD - F255RHC MITER CHOP SAW
|
|
Price: $3,095.00
Machine Stock Number: F255RHC-Q
Condition: New
FOB: CA-L.A.
Electrical: 230/460 V, 3 Ph, 60 Cy
|
|
Description:
MODEL F255RHC Overhead cut off saw 14" NON-MITERING 90 degree cut only with 14” blade capacity - 1" bore; 2 HP, 1 phase 230 volt or 3 HP, 3 phase 230 volt TEFC motor; V-Belt drive includes rotating blade guard with 2” dust outlet, less blade. Standard machine with full table base, 2 keyed sliding fences and manual overload starter. $3,095.00
MODEL M25RHC Overhead cut off saw 14" MITERING with indexing
angle presets; standard machine with full table base as above $3,495.00
Options:
FSD - Enclosed floor stand with dust pan and 4" dust outlet $ 495.00
MAG – Magnetic starter – OSHA required; gives motor high
and low voltage protection with fuse protection and disconnect
switch; not available for single phase, 110 volt motors $ 350.00
VOLT – Voltage change - to change voltage from 220 volt to
either 110 or 440 volt (no charge if Magnetic Starter is purchased) $ 75.00
LEFT – Left Hand Assembly – opposite of standard arm; to
feed material to the right $ 120.00
AF – Air Power Feed Unit – for precision, controlled cutting
on wood, plastic or non-ferrous sections; actuated by SAFETY
ANTI-TIE DOWN, MAINTAINED CONTACT TWO-HAND
CONTROL. Air vales are mounted above the saw head and reverse
when two-hand control is released; includes one AIR CLAMP,
FOOT VALVE to actuate clamp and AIR FLITER/EGULATOR/
LUBRICATOR UNIT with AUTO DRAIN. $1,795.00
HYD – Air Haydraulic Power Feed Unit – same as AF but uses a
Hydrocheck Unit with Air Cylinder for controlled down stroke
speed, includes FV to actuate clamps. $2,450.00
VC3/200 Vertical Air Clamp $ 215.00 ea.
HC/200 Horizontal Air Clamp $ 230.00 ea.
AV/200 Auto valve actuator IF AF or HYD not ordered and clamps
or spray mist are added $ 100.00
QV - Quick action manual vise clamping $ 295.00
FR – Combination Air Filter/Regulator/Lubricator – to clean
incoming air; with Auto Drain $ 200.00
SLS/200 Saw blade lubrication system for non-ferrous cutting $ 275.00
SOL/ Souluable oil solution for spray mist, 1 gal. $ 30.00
RC-10 – Roller Conveyor – fastened to Floor Stand, one leg and
seven rollers per section; 10’ long $ 595.00
RC-5 -- Roller Conveyor as above but 5' long $ 375.00
EXF/16 Extended Fence Length Guage measures material cut-off
lengths up to 192” (16’); 2” high x 16’ long fence with tape scale
(right to left or left to right - specify) $ 375.00
ASTP Air Stop – push the button to move the stop to desired
location along tape scale, release to lock in position. $ 295.00
Terms: 30% down with order, balance net 30 with approved credit.
|
|
|
|
|
|
|
1-10 || 11-20 || 21-30 || 31-37 |
Last Updated: 8/6/2010
|
|
